Imprint

Address:
HOLZ-HER GmbH
Großer Forst 4
72622 Nürtingen
Germany

Tel.: +49 (0)7022 702 – 0
Fax: +49 (0)7022 702 – 101
info@holzher.com
www.holzher.de

Managing director: Robert Terzer
Commercial register number: Stuttgart HRB 733620
VAT / ID-Nr.: DE 815169 432

HOLZ-HER GmbH is a company of Michael Weinig Aktiengesellschaft

Incorporated company with its registered office in 97941 Tauberbischofsheim

Address: 
Michael Weinig Aktiengesellschaft 
Weinigstrasse 2/4 
97941 Tauberbischofsheim 
Germany

Tel.: +49 9341 860
Fax: +49 9341 7080
info@weinig.com

Company name: 
Michael Weinig Aktiengesellschaft

Represented by the management board:
Gregor Baumbusch (CEO)
Dr. Georg Hanrath

Chairman of the supervisory board
Dr. Thomas Bach

Honorary member of the supervisory board:
Ali M.T. Alghanim

VAT / ID No.: 
DE 146587898

Commercial register number: 
HRB 560227
District court Mannheim

Liability for content

The content of our website has been compiled with great care. However, we can assume no liability for the correctness, completeness or currency of its content. As a service provider, we are responsible for our own content on the site in accordance with general legislation, pursuant to § 7 para.1 of the German Telemedia Act (TMG). However, in accordance with §§ 8 to 10 of the TMG, we are not obliged as a service provider to monitor transferred or stored third-party information or to investigate circumstances suggesting illegal activities. Obligations to remove or block of the use of information in accordance with general legislation remain unaffected by this. However, liability in this respect shall only be possible from the moment that knowledge of a concrete infringement of law is obtained. Upon becoming aware of such infringements of law, we will remove such content immediately.

Liability for links

Our website contains links to external websites of third parties. We have no influence on the content of these. Therefore, we cannot accept any liability for such third-party content. Responsibility for the content of linked sites always lies with the relevant provider or operator. Linked sites were checked for potential legal infringements at the time of linking. No illegal content was identifiable at the time of linking. However, permanent monitoring of the content of linked sites is not reasonable without concrete evidence of an infringement of the law. Upon obtaining knowledge of infringements of law, we shall remove such links immediately.

Copyright

Content and work compiled by website operators on these pages are subject to German copyright law. Reproduction, processing, distribution and any other form of re-use beyond the scope of copyright law requires the written consent of the relevant author or creator. Downloads and copies of this website are only authorized for private use and not for commercial use. Where the content of this website has not been created by the operator, the copyright of third parties has been observed. In particular, third-party content is indicated as such. However, should you notice a breach of copyright, we would be grateful if you would notify us accordingly. Upon obtaining knowledge of infringements of law, we shall remove such content immediately.

Technical data

The technical data are approximate values. Changes of construction and equipment reserved, since HOLZ-HER machines are constantly evolving. The illustrations are not binding. The machines include special equipment which are not part of the standard scope of delivery. For better information, the machines were imaged in part without the provided protective cover.

Prices

Prices shown on the website are not binding. The automatic dispatch of offers does not constitute a binding offer.

Country-specific versions

The international spread of the World Wide Web implies that these pages refer to products or services that are not available or not under another name and in another embodiment in your country.

ZENTREX_6215_lift_2020_rechts

ZENTREX lift

TECHNICAL DATA
  • Year of production: 10/2018
  • Cutting length: 4300 mm
  • Cutting width: 4200 mm
  • Charging: Hydraulic scissor lift table incl. thin plate push-off device > 4mm
  • Saw blade projection: 115 mm
  • Power: 15 kW | 2,2 kW
  • Feed rates: 100 m/min | 25 m/min
  • Machine / support tables: with air cushion
  • Workpiece indication: Laser Indicator
  • Clamps: 10 intelligent workpiece clamps (incl. 3 double-finger clamps)
  • Label printer and software
  • Control: Multitouch 21,5″ with CutControl 2
  • Optimization: Machine & office licenc
  • Smart Factory ready

Attention: All machines are subject to prior sale

TECTRA power

TECHNICAL DATA
  • Year of production: 2020
  • Cutting length: 3100 mm
  • Cutting width: 3100 mm
  • Saw blade projection: 95 mm
  • Power: 11 kW | 2,2 kW
  • Feed rates: 100 m/min | 25 m/min
  • Machine / support tables: with air cushion
  • Clamps: 5 Pieces (incl. 3 Double-finger clamps)
  • Label printer and software
  • Control: Multitouch 21,5″ with CutControl
  • Optimization: Machine & office licenc
  • Smart Factory ready

Attention: All machines are subject to prior sale

TECTRA Classic

TECHNICAL DATA
  • Year of production: 2020
  • Cutting length: 3100 mm
  • Cutting width: 3100 mm
  • Saw blade projection: 82 mm
  • Power: 11 kW | 2,2 kW
  • Feed rates: 70 m/min | 25 m/min
  • Machine / support tables: with air cushion
  • Clamps: 5 Pieces (incl. 3 Strip clamps)
  • Label printer and software
  • Control: Multitouch 21,5″ with CutControl
  • Optimization: Machine & office licenc
  • Smart Factory ready

Attention: All machines are subject to prior sale